seametrics

Magnetic Flow Meter iMAG series Seametrics

Diposkan pada Mei 20, 2016Juni 13, 2017 oleh Yugo Nugroho Boyolali

The iMAG 4700 magnetic flow meter is the most economical flange electromagnetic flowmeter on the market produced by seametric instrument . With electrodes designed to discourage fouling, it is available in 4” to 12” pipe in municipal or industrial water, waste and reclaimed water, pump stations, and packaged plant applications. (For 3” version, see iMAG 4600-300.) Minimal straight pipe requirements allow.

iMAG magnetic flow meters to be used in piping configurations where there is little space between the meter and an elbow.

Water flow meter iMAG 4700 are NSF-61 approved and are rated IP68 for applications where the meter may be operated under water to a depth of at least 10 feet (3 meters) continuously.

The display magmeter iMAG 4700 can be meter mounted or remote, and both rate and total indication are standard. Rate and total units and pulse scaling can be set via the front panel touch key pad by the user. Bidirectional flow is standard with forward, reverse and net flow.

A power/output cable imag water flow meter allows outputs for use with a variety of Seametrics inc USA and other displays and controls for remote reading and telemetry applications. Pulse output is standard on all models and 4-20mA passive current loop is standard on the iMAG 4700p. In addition, 4-20mA loop, HART protocol, high speed digital, and Modbus® protocol outputs are optional on the externally powered units, depending on model.

Features

Easy setup
Minimal straight pipe
Mounted or remote rate & total
Tamper-evident seal
NSF-61 approved
IP68 rated

iMAG Water Meter Accuracy

These magnetic flow Meter can be installed horizontally, vertically (with downward flow), or in any radial position. Using a check valve on the upstream side of the meter, and/or an air vent (vacuum relief valve) in the same, unobstructed run of pipe as the meter, is required in any installation where the meter may be exposed to suction when the system is not in normal operation. Suction can cause damage to the liner. Liner damage caused by suction, without the use of a check valve and/or air vent, may void the warranty.

iMAG 4700 Dimension

iMAG water flow meter straight Pipe Recommendations.

The iMAG magnetic flow meter requires straight pipe before and after the meter for best accuracy. However, the ability of electromagnetic meters to average the flow across the entire pipe allows for shorter straight pipe recommendations than most mechanical meters

rudy

Pulse Output Configuration.

A pulse output is standard on all models. Since this is an isolated output, the external equipment must include a DC power source to regenerate the pulse from the open-collector output (transistor equivalent of a contact closure). A pull-up or pull-down resistor may be needed if not included in the user equipment as shown in the diagrams.

Both the power source and resistor may be supplied internally in some types of control and monitoring magnetic flow meter devices. If not, as for most PLC discrete input modules, they must be added externally at the module input terminals. The pulse output rate in volume units/pulse can be set by the user via the SET P tab on the meter’s setup menus.

iMag Flow Rate Table

Battery Powered Units

The iMAG 4700 flow meter can come configured with two replaceable 3.6V lithium ‘D’ batteries. In this configuration, the only option/output is the scaled pulse output which comes standard. The scaled output for the battery powered option has a maximum pulse rate of 150 pulses/second, with a fixed pulse width of 2.5ms. Be sure to set your P value such that the meter will function properly over the flow range in your flow meter application. The sample rate of the meter is user selectable through the SAMP tab in the meter’s sub-menu. Sample periods of 1/5, 1/3, 1, 3, 5, 15, 30, and 60 seconds can be selected. Larger sample periods will yield longer battery life but slower response time. Care must be taken to select a sample period that is suitable for your application. See the table below for the expected battery life as a function of sample period

Ultrasonic Flow Meter jWAVE

Diposkan pada September 29, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

Portable Ulrasonic Flow Meter
Ultrasonic Flow Meter jWAVE
Now you can capture accurate and reliable flow readings with your mobile device, with less hassle and in less time—wherever you need a flow or volume measurement.

No wires. No bulky electronics box to lug around. Your ultrasonic sensor hardware installs on the outside of your pipe in a snap—and senses through the pipe wall. Your mobile device displays readings and helps you set up the hardware.

And Bluetooth replaces the wires.
So you’ll get your job done more quickly, every time. What’s the jWAVE?
The jWAVE Flow Meter solution starts with the jWAVE App (downloadable from the app stores) and works on both iOS and Android devices.

The companion jWAVE Sensor is a compact, clamp-on ultrasonic transducer device that wirelessly transmits flow measurements. With a programmable controller, the output signal can be fed direct, with no other conditioning required.

The jWAVE is highly portable. Just bring the rechargeable clamp-on sensor in its lightweight, weatherproof case, along with a tablet or smartphone (iOS or Android). Bluetooth connectivity replaces wires, and the jWAVE App guides you through your application setup.

The convenient Cam Cleat lets you mount the sensor on any pipe in seconds—no cumbersome clamps required. Bi-directional readings are transmitted to your mobile device for display, and your location’s settings are stored in the jWAVE App, ready for reuse.

Now simply release the cleats, then take the compact sensor on to your next location.

Paddle Wheel Flow Meter

Diposkan pada September 29, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

The IP100/200-Series are adjustable depth insertion paddle wheels that come in brass, PVC, or 316 stainless models to fit 3” to 40” pipe. Adapters mate with standard 1-1/2” (11x/21x) or 2” (15x/25x), or PVC (11x/21x) NPT threaded fi ttings such as saddles and weldolets which may be purchased either locally or from Seametrics.

Ruby bearings and a non-drag Hall-effect sensor give these meters the widest fl ow range of any of the paddle wheel types. A sensor detects the passge of miniature magnets in the six rotor blades. The resulting square-wave signal can be sent for hundreds of feet over unshielded cable without a transmitter and connected directly to many PLC’s and other controls without any additional electronics.

A modular system of electronics can be installed directly on the flow sensor or mounted remotely. The FT430 (externally powered with pulse), FT440 (loop powered), and FT450 (battery powered) all provide digital rate and total displays, as well as a programmable pulse; the FT440 also provides a 4-20 mA analog output. The AO55 is a blind analog (4-20 mA) transmitter. Programmable pulse for pump pacing is available with the PD10.

The “hot-tap” models (IP15x/25x) can be installed or serviced without shutting down the line by means of a 2” full-port isolation valve that comes with a nipple for installation on the pipe fitting.In most circumstances, no special tool is required.

Electromagnetic Flowmeter WMX Series

Diposkan pada Agustus 22, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

The WMX-Series are fanged electromagnetic fow meters for use in 4” to 10” pipe in municipal or industrial water and waste water applications where propeller meters have typically been used in the past. Because the WMX has no moving parts and has electrodes designed to discourage fouling, this magmeter performs well and requires much less frequent maintenance in applications where debris would impede propeller meters.

There is no rotor to stop turning or bearings to wear out. Minimal straight pipe requirements allow WMX-Series meters to be used in piping confgurations where there is little space between the meter and an elbow.In chemical injection applications, the meter should be placed upstream of the injection line or far enough downstream for thorough mixing to occur before the meter.Rate and total indication are standard on both models.

Units are customer-selected and factory-set. No set-up is required.The WMX101 is externally powered with 7-26 Vdc at 30 mA max (see NOTE in Specifcations). Two Lithium 3.6V “AA” batteries provide auxiliary power during power failures, allowing the meter to continue recording fow rate and total without interruption for the duration of the outage. Where external power loss is infrequent, battery life should exceed 10 years.

The 20-foot power cable also provides pulse output for use with a variety of Seametrics and other displays and controls for remote reading, data logging, pulse-to-analog conversion, and telemetry applications. High frequency pulse rate (required for use with 4-20 mA converters) is standard; additional pulse rates are optional.

The WMX104 is a battery-operated unit for use when pulse output is not required. The Lithium 3.6V “D” batteries are replaceable with an approximate 1-year life under continuous use, or more depending on the duty cycle. An optional input/output cable can be installed post-factory if needed for changing applications.

FEATURES

Simple and economical as a mechanical meter
No moving parts
Built-in pulse output
Minimal straight pipe required
Continuous battery or external power
Data logger compatible
Telemetry-ready

APPLICATIONS

Municipal water/waste water
Industrial water/waste water
Cooling tower water treatment
Well usage reporting

Specification

Electromagnetic Flowmeter EX800 Series

Diposkan pada Agustus 22, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

Description :
– Low-flow performance and accuracy superior to any mechanical flow sensor
– No moving parts to wear out
– Dedicated fittings for simplicity
– Retainer clip automatically sets correct depth
– Meter extends only about 1/8 of pipe diameter, minimizing potential for clogging with debris
– Simple pulse train output can be used with any SeaMetrics signal processing module, or sent directly to a PLC
– Available for pipe sizes 1″ to 8″, in brass, 316 stainless, and PVC

Electromagnetic Flowmeter EX110 Series

Diposkan pada Agustus 22, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

Description :
– Depth adjustable sensors
– EX110 fits any 1-1/2″ pipe fitting (standard saddle, for instance) and adjusts to pipe sizes 3-10″
– EX210 adjusts to pipe sizes 10-48″
– Meter extends only about 1/8 of pipe diameter, minimizing potential for clogging with debris
– Accept Seametrics modules for rate and total indication, 4-20 mA conversion, data logging, and flow switching
– Alternatively, signal can be sent directly to a PLC or other control
– Available in brass or 316 stainless steel
– Immersibility and reverse flow output available

Seametrics Flow Batch Controls

Diposkan pada Februari 16, 2015 oleh Yugo Nugroho Boyolali

The FT500-Series is a batching fow processor with additional output controls. It is designed for use with Seametrics fow meters and fow sensors, as well as other manufactuer’s products which have frequency output proportional to fow.

In addition to batch functions, the FT500-Series indicates fow rate, and other data in large 3/8” (9.66 mm) digits on an easily-read, backlit display. Units of measure are user selectable, and range from milliliters per second to millions of gallons per day. The unit can be 110 Vac powered with a standard 3-wire cord (included), 220 Vac powered (optional), or DC powered through an internal terminal strip (battery not included).

Large backlit alphanumeric display

Built-in 4-20 mA analog output

User-scaled pulse output for chemical metering pumps or telemetry

Two relay outputs for staged shutoff (batching) or dual setpoints (alarm option)

Rugged cast aluminum housing

Wall or panel mounting

An analog output of 4-20 mA is available both in active and passive loop confguration, and in 0-5 Vdc or 0-10 Vdc outputs, and can be used in applications such as fow rate logging. Two programmable pulse scaled outputs are also standard, and can be used, for example, to provide proportional chemical feed with a pulse-responsive metering pump.The housing is supplied with two brackets for wall-mount applications, or the top/bottom housings can be easily separated and reassembled for panel-mount.

FEATURES

• Batch control

• Regeneration control

• High/low fow rate monitoring

• Water usage monitoring

APPLICATIONS
• Cosmetics manufacturing
• Water treatment system maintenance
• Water leakage detection
• Precision refll of cooling towers & tanks

Seametrics Analog Transmitter

Diposkan pada Februari 16, 2015 oleh Yugo Nugroho Boyolali

SEAMETRICS FLOWMETER – AO55 SERIES – BLIND ANALOG TRANSMITTER

Two-wire 4-20 mA output

Precise manual setting of the 20 mA flow rate

Rugged cast aluminum housing with fused coating

Electronic components potted in urethane for maximum moisture protection

Can be meter or wall mounted

Test switch to force 4 and 20 mA outputs

Variable averaging to smooth output from particularly turbulent flows

The Seametrics AO55 is a blind (non-indicating) 4-20 mA transmitter, designed for use with almost all Seametrics fow sensors. It accepts a pulse frequency input from the fow sensor, and converts this input into a continuous analog output signal. Power for the transmitter is taken from the current loop itself, so only two wires are required. The digital design makes it possible to span the unit in the feld without tools. The frequency at which 20 mA is desired is entered on a set of rotary switches, and an internal microcontroller automatically scales all other values accordingly. An additional beneft of the microcontroller is its ability to average inputs,
for smoothing of the output signal. The degree of averaging can be selected in the feld, from 2 to 16 seconds.
For maximum environmental protection, the electronic components are encased in a special semi-fexible urethanepotting material. The housing is cast from aluminum and fuse-coated. The clamshell housing is connected directly to the fow sensor or, in the wall mount version, provided with mounting feet.
The AO55 will operate on a relatively wide range of current loop voltages, 24 to 36 Vdc. Lower voltages limit the load
that can be applied to the loop without distortion of the signal. (See Load/Supply chart if there is a question regarding voltage vs. load.) A built-in power regulator supplies the appropriate power to the fow sensor.
Typical applications for this transmitter are telemetry (or SCADA), distributed control systems, programmable controllers, data logging, and chart recording.

APPLICATIONS
• Telemetry/SCADA
• Distributed control systems
• Programmable controllers
• Chart recording
• Data logging

FEATURES
• Pulse-to-analog converter
• Current loop powered
• Smooth output signal
• Easy set-up
• Durable

Seametrics Data Logger

Diposkan pada Februari 16, 2015 oleh Yugo Nugroho Boyolali

The DL76 is a battery-powered data logger that can be used with any Seametrics fowmeter. It stores pulses for up to 3 years, depending on the user-selected frequency of reading. Indicator lights on the unit fash to indicate when it is functioning and when the battery is low.

The DL76 can be factory-mounted on the meter or remotely mounted. Housings are rugged cast aluminum, gasketed for environmental protection.

When a DL76 logger is placed into operation, it is easily set up using a laptop computer. Data is also retrieved from the DL76 by means of a laptop and can be analyzed on the laptop or easily loaded on a desktop computer for analysis.

DL 76 Data Logger

Battery-powered data logger

3.6 Vdc lithium battery included, 3-year battery life

Compatible with any Seametrics flowmeter

Uses Seametrics FlowInspector Version 2 software

Stores pulses for up to 3 years (depending on sampling interval)

Available in meter-mount or wall-mount models

Data retrieval by laptop computer

Single data retrieval device serves multiple data loggers

*FlowInspector version 2 software (ordered separately) is required for the downloading, storing, viewing, graphing, charting and printing of data in several formats. FlowInspec-tor requires a PC with Windows 98, NT, 2000, XP, Vista or Windows 7; CD-Rom drive; 800 x 600 screen resolution; serial port or USB/serial adapter; and a Seametrics DC3 data cable. FlowInspector can be used with an unlimited number of dataloggers.

*Older versions of FlowInspector are not compatible with the DL76.

FEATURES
• Easy to set-up, easy to use
• Weeks/months/years of data storage
• User-selected sampling interval
• Data retrieval with laptop computer
• Single data retrieval device serves
multiple data loggers

APPLICATIONS
• Water usage monitoring, reporting,
and management
• Custody transfer regulation
• Peak demand monitoring

Seametrics Flow Measurement

Diposkan pada Februari 16, 2015Juni 13, 2017 oleh Yugo Nugroho Boyolali

Seametrics Inc. is a designer and manufacturer of a wide variety of flow metering products. Since 1990 the company has provided innovative solutions to users in industrial water treatment, energy management, irrigation, utilities, transportation, and chemical handling. Seametrics products have a reputation for durability and accuracy at a competitive price, and are sold largely through a network of domestic and international distributors.

Seametrics Flow Meter

Seametrics flow measurements is committed to providing a broad range of flow metering products for the Industrial/Municipal and Irrigation industries in addition to a variety of OEM applications. We maintain an attitude of responsiveness to the many flow metering needs encompassed within these industries and are vigilant in our efforts at developing new flow meter products and enhancing our existing products to better serve our customers.

Since 1990, Seametrics flow measurement has been providing high-value flow meters and controls. The guiding principles have been common sense, simplicity, economy and durability. We started with mechanical insertion meters that extended the bottom of the flow range and were easy to repair. Over the years our flow meter product family has expanded to include electronic turbine flow meters, inexpensive and highly accurate mechanical low-flow meters, and a variety of flow meter controls and displays. In recent years Seametrics flow meters has become a leading manufacturer of electromagnetic meters (mag meters) in a variety of designs suitable to a wide range of applications. These include insertion, spool, and low-flow chemical-resistant mag meters.

ELECTROMAGNETIC FLOWMETER